USB Interface Modules

FE-359-USB Interface Module

2 x 8 channel 16 bit A to D converters with USB 2.0 interface. 16 x 25 kS/s.

The module can only be fitted in a FE-MM16 chassis.

Specification

• Analog Inputs: 16 +/- 10 V signals from eight dual channel transducer interface modules.
• Resolution: 16 bit.
• Range: +/- 10 V.
• Sampling Rate: Maximum 16 x 25 000 samples per second.
• Offset: < +/- 5 mV.
• Noise: < 2 mV pk-pk.
• Crosstalk: -95 dB at 25 kS/s with 5 kHz sine wave input.
• Gain Error: < 0.1%.
• USB Standard: USB Specification Revision 2.0.

FE-357-USBM Interface Module

The FE-357-USBM works with an external multiplexer to provide 40 channels of A to D conversion.

This module can only be used in the FE-MM40 chassis.

Specification

• Analog Inputs: 40 +/- 10 V signals from twenty dual channel transducer interface modules.
• Resolution: 16 bit.
• Range: +/- 10 V.
• Sampling Rate: Maximum 40 x 10 000 samples per second.
• Offset: < +/- 5 mV.
• Noise: < 2 mV pk-pk.
• Crosstalk: -95 dB at 25 kS/s with 5 kHz sine wave input.
• Gain Error: < 0.1%.
• USB Standard: USB Specification Revision 2.0.

FE-356-USB Interface Module

The FE-356-USB module makes the FE-MM8 into a complete USB data acquisition system.

The module not only handles the flow of the sampled data to the host computer, but also maintains the auto zero function for any installed transducer amplifiers.

USB technology is plug and play so your computer will automatically recognise the FE-356-USB as a new device and install the software for it.

8 channel 16 bit A to D converters with USB 1.1 interface. 8 x 50 kS/s.

This module provides all the functions of the Auto Zero module and the USB interface.

The module can only be fitted in a FE-MM8 chassis.

Specification

• Analog Inputs: 8 +/- 10 V signals from four dual channel transducer interface modules.
• Resolution: 16 bit.
• Range: +/- 10 V.
• Sampling Rate: Maximum 8 x 50 000 samples per second.
• Offset: < +/- 5 mV.
• Noise: < 2 mV pk-pk.
• Crosstalk: -95 dB at 50 kS/s with 5 kHz sine wave input.
• Gain Error: < 0.1%.
• USB Standard: USB Specification Revision 2.0.

FE-356-USB Interface Module

The FE-356-USB module makes the FE-MM8 into a complete USB data acquisition system.

The module not only handles the flow of the sampled data to the host computer, but also maintains the auto zero function for any installed transducer amplifiers.

USB technology is plug and play so your computer will automatically recognise the FE-356-USB as a new device and install the software for it.

8 channel 16 bit A to D converters with USB 1.1 interface. 8 x 50 kS/s.

This module provides all the functions of the Auto Zero module and the USB interface.

The module can only be fitted in a FE-MM8 chassis.

Specification

• Analogue Inputs: Quantity: 4 signals from two dual channel transducer interface modules.
• Operating Range: ±10 V relative to Analogue 0 V. Note that these inputs signals remain available as system analogue outputs on the 9 way D connector at the rear of the FE-MM4.
• Function: Shunt Calibration for FE-366-TA channels.
• Resolution: 16 bits.
• Range: ±10 V.
• Sampling Rate: Maximum 4 x 100 000 samples per second.
• Offset: < ±5 mV.
• Noise: < 2 mV pk-pk.
• Crosstalk: -95 dB at 50 kS/s with 5k Hz sine wave input.
• Absolute Gain Error: < 0.25 % (See Note 2).